Series 12 LED Wall Mount 2 Engine Specifications

CONSTRUCTION

Body is 20-gauge die-formed steel with an 18-gauge die-formed internal joiner system. Plugtogether wiring standard. All components are hard-tooled to tolerances of +/- 0.010".

ENDCAPS

The Flat Endcap (FE) is standard and made of 20-gauge die-formed steel adding 0.1" at each end. The optional Curved Endcap (CE) is an aluminum die-cast endcap with a 0.100" reveal adding 5.0" at each end.

OPTICS

SHIELDING

LIGHT OUTPUT

Four lumen packages available, Standard (S), Boosted Standard (B), High (H), and Very High (V). A separate chart summarizes lumen distribution and wattage. Light engines are replaceable.

LUMEN MAINTENANCE

90% of initial light output (L90) at 100,000+ hours; 70% of initial light output (L70) at 200,000+ hours.

DRIVER

Replaceable 120V/277V Constant Current Reduction dimming driver standard. Can be wired dimming or non-dimming. 0-10V dimming controls with a range of 10%-100%. Dimming to 1% available; consult factory. Driver is fully accessible from below the ceiling. Power Factor: ≥ 0.9. Total Harmonic Distortion (THD) < 20%. Expected driver lifetime: 100,000 hours.

LUTRON DRIVER OPTIONS

Lut3W-3-wire, LutESEcoSystem, Lut2W-2-wire.

INTEGRATED SENSORS

Integrated PIR (Passive Infrared) occupancy and/or daylight sensors available. Refer to Occupancy Sensor and Daylight Sensor tech sheets for more info.

ELECTRICAL

Optional emergency to generator/inverter wiring, internal generator transfer switch, nightlight wiring, step-dimming driver, backup battery. A factory-choice low-profile backup battery is available (8' minimum fixture length). Backup batteries deliver 1600 lumens. A 4' section will be illuminated in emergency mode.

MOUNTING

Standard Surface Mount (SUR) - fixture is bolted directly into existing wall studs. Optional Standoff Mount (SO) - fixture hangs from tapered mounting bracket fastened to wall at fixture ends and joints; standoff bracket measures 4.5" wide, 6.0" tall, and 0.5" deep; fixture hangs 0.5" from wall; feed goes through mount to vertical J-box. Optional Mounting Bracket (MB) - fixture hangs from bracket fastened directly to wall; mounting bracket available in 4' and 8' lengths; fixture hangs 0.5" from wall; mounting bracket is concealed behind fixture.

FINISHES

Finelite Signal White powder coat standard. Optional Adders: 185 Tiger Drylac’s non-metallic RAL colors.

FEED

Standard with one 18-gauge/5-conductor singlecircuit feed. 14-gauge feed used when fixture current exceeds 5 amps.

LENGTHS

Standard 4' and 8' section lengths can be combined to make longer runs. Contact factory additional lengths.

LABELS

Fixture and electrical components are ETL-listed conforming to UL 1598 in the U.S.A. and CAN/CSA C22.2 No. 250.0 in Canada. In accordance with NEC Code 410.73 (G), this luminaire contains an internal driver disconnect. Damp Location. Finelite products use electronic components that are RoHS compliant, and the mechanical components of the luminaire have been verified to not knowingly contain any restricted substances listed per RoHS Directive 2002/95/EC.

WEIGHT

With Flat Endcaps (FE) - 2.0 lb/ft; with Curved Endcaps (CE) – 2.6 to 3.6 lb/ft.

DLC QUALIFIED

Configurations of this product are listed on the DLC Qualified Products List (QPL).

WARRANTY

10-year performance-based warranty on all standard components. Optional accessories such as emergency battery packs are covered by their individual manufacturer warranties.