Series 12 LED 2 Engine Specifications

CONSTRUCTION

Body is 20-gauge die-formed steel with an 18-gauge die-formed internal joiner system. Plugtogether wiring standard. All components are hard-tooled to tolerances of +/- 0.010".

ENDCAPS

The Flat Endcap (FE) is standard and made of 20-gauge die-formed steel adding 1/8" at each end. The optional Curved Endcap (CE) is an aluminum die-cast endcap with a 1/8" reveal adding 5.0" at each end.

OPTICS & DISTRIBUTION RATIOS

Open
FTO
CTO
TDO
10U90D
20U80D
30U70D
40U60D

Standard (2E, 3E)
Frosted Top Optic (2E, 3E)
Clear Top Optic (2E, 3E)
Total Direct Optic (2E, 4E)
10% up / 90% down (2E, 4E)
20% up / 80% down (2E, 4E)
30% up / 70% down (2E, 4E)
40% up / 60% down (4E ONLY)

SHIELDING

DCO

Diffuse Center Optic, 73% transmissive, 99% diffusion.

WCB

White Cross Baffle, 87 cell baffles spaced 1/2" apart and finished with 96% reflective white paint.

PLV

Parabolic Louver, Semi-specular louvers with straight edges, spaced approximately 1 3/16" apart.

Visible diffuser: UV-stabilized and impact-resistant frosted virgin acrylic, 1/8" thick. Inner diffuser: 1/8" thick with 40% round perforations white/white.

LIGHT OUTPUT

2E & 3E; Four lumen packages available, Standard (S), Boosted Standard (B), High (H), and Very High (V).

4E; three lumen packages available, Standard Output (S), 3000 lumens, Boosted Standard (B), 4000 lumens, High Output (H), 5000 lumens.

A separate chart summarizes lumen distribution and wattage. Light engines are replaceable.

LUMEN MAINTENANCE

90% of initial light output (L90) at 100,000+ hours; 70% of initial light output (L70) at 200,000+ hours.

DRIVER

Replaceable 120V/277V Constant Current Reduction dimming driver standard. Can be wired dimming or non-dimming. 0-10V dimming controls with a range of 10%-100%. Dimming to 1% available; consult factory. Driver is fully accessible from below the ceiling. Power Factor: ≥ 0.9. Total Harmonic Distortion (THD): < 20%. Expected driver lifetime: 100,000 hours.

LUTRON DRIVER OPTIONS

LutES1 (Hi-lume 1% EcoSystem with Soft-On, Fade to Black dimming (LDE1 series)); LutES5 (5-Series 5% EcoSystem (LDE5 Series)), Lut2W (Hi-lume 1% 2-wire, 120V forward phase dimming (LTEA series)); Contact factory for availability of discontinued Lutron drivers, L3DA-3-wire and L3DA EcoSystem.

ELECTRICAL

Optional emergency to generator/inverter wiring, internal generator transfer switch, nightlight wiring, step-dimming driver (B and V outputs only), backup battery.

2E PENDANT: A factory-choice low-profile backup battery is available (8 ft. minimum fixture length). Backup batteries deliver 2392 lumens. A 4 ft. section will be illuminated in emergency mode.

3E PENDANT: A factory-choice low-profile backup battery is available (8 ft. minimum fixture length). Backup batteries deliver 2027 lumens. A 4 ft. section will be illuminated in emergency mode.

4E PENDANT: A factory-choice low-profile backup battery is available (8 ft. minimum fixture length). Backup batteries deliver 2027 lumens. A 4 ft. section will be illuminated in emergency mode.

INTEGRATED SENSORS

Integrated PIR (Passive Infrared) occupancy and/or daylight sensors available. Refer to Occupancy Sensor and Daylight Sensor tech sheets for more info.

MOUNTING

50" Fully Adjustable (FA) plated steel aircraft cable with safety stop hardware standard. Contact factory for additional lengths up to 150". Optional semi-adjustable Aircraft Cable (AC) (± 0.5") in lengths of 12", 15", 18", 21", 24", 27", 30", and 36".

FINISHES

Finelite Signal White powder coat standard. Optional Adders: 185 Tiger Drylac’s non-metallic RAL colors.

FEED

Standard with one 18-gauge/5-conductor singlecircuit feed. 14-gauge feed used when fixture current exceeds 5 amps.

LENGTHS

Standard 4 ft. and 8 ft. section lengths can be combined to make longer runs. Contact factory additional lengths.

LABELS

Fixture and electrical components are ETL-listed conforming to UL 1598 in the U.S.A. and CAN/CSA C22.2 No. 250.0 in Canada. In accordance with NEC Code 410.73 (G), this luminaire contains an internal driver disconnect. Damp Location. Finelite products use electronic components that are RoHS compliant, and the mechanical components of the luminaire have been verified to not knowingly contain any restricted substances listed per RoHS Directive 2002/95/EC.

WEIGHT

With Flat Endcaps (FE) - 2.0 lb/ft; with Curved Endcaps (CE) – 2.6 to 3.6 lb/ft.

DLC QUALIFIED

Configurations of this product are listed on the DLC Qualified Products List (QPL).

WARRANTY

10-year performance-based warranty on all standard components. Optional accessories such as emergency battery packs are covered by their individual manufacturer warranties.


© Finelite, Inc. All rights reserved. Contact Us \| Privacy Policy \| Sales Terms and Conditions \| Site Map